Specifikacije medija koje možete koristiti s Primera CX1200 printerom za etikete

 What brands or types of media does Primera recommend to use with the CX1200?

Primera recommends using Primera brand label stock.

The following additional non-Primera brand label stocks are approved for use in the CX1200. All stock must be converted to 8.5 width roll with 12" outer diameter on a 3" ID core.

- Mactac LAS1812 White Matte Paper Stock (4.0 mil)
- Mactac LAS1812 White High Gloss Paper Stock (4.0 mil)
- FilmLOC LaserLOC White Gloss Polyester (2.0 mil)
- FilmLOC LaserLOC Clear Gloss Polyester (2.0 mil)

Other media may also be officially approved in the future. If you are not using approved media, it should have the following characteristics.

Paper Type

The CX1200 can only print on Laser Printer approved materials. The label manufacturers specifications will always say whether material is laser approved. If it does not say laser approved it probably is not laser-approved. Be sure that the laser approval applies to the face stock material, the adhesive and the liner. Stocks must be laser approved because the fuser roller contacts the paper at 356 F / 180 C. At this temperature facestock or liner material could melt or burn. Non-laser-approved adhesives could lose adhesion.

Do NOT attempt to print onto non laser-approved materials. Damage to your printer may result which will not be covered under your limited warranty. POLYPROPYLENE AND SOME OTHER SYNTHETIC MATERIALS WILL MELT. Do not ever attempt to print onto polypropylene or any other similar low-temp substrates.

Polyester and Paper generally will perform well in the CX1200.

Thickness(Facestock only)

Mil = 2 - 6
Caliper(Inches) = .002 - .006
Millimeters = .0508 - .15
Grams/sq meter = 34 - 116

**Above does not include standard 3 mil liner

Paper stock in the above range will feed through the CX1200 printer with out problems. Depending upon operating environment, Polyester stocks in this range will also feed through the printer with out problems. However, 2-3 mil Polyester does curl as it exits the printer. In more humid environments this curling becomes more severe and could cause the paper to jam before it enters the fuser. Stock thicker than 6 mill will intermittently jam before entering the fuser. This can be solved by attaching a thinner leader material to the thicker stock.

When testing other media consider the following additional criteria:

1 Print Quality / Poor Transfer - See Note 1.
2. Color Accuracy
3. Solid Color Saturation
4. Label Feed (Requires minimum 100 feet of test paper.
5. Label Wrap
6. Fuser Heat tolerance - wrinkling, bubbling, burning, Breaking, Curling.
7. Water Tolerance
8. Scratch Tolerance
9. Cut quality
10. Lamination Quality

Note 1: Test at least 100 feet of continuous material before determining compatibility. Some Plastic stocks will initially appear to be compatible. However over time, the material absorbs too much heat so that not enough is left over to fuse the toner to the surface of the material.

Other Warnings.

Do NOT print on die-cut label materials or on web widths of less than 8.5” (215mm). Labels should always be die-cut as a post process on a separate piece of finishing equipment. Printing on die-cut materials is dangerous. Adhesive bleed can easily ruin the Image Transfer Unit (ITU) and fuser. A label that pre-dispenses inside the unit can cause physical damage to the printer.

Primera je počela sa prodajom novog laserskog pisača CX1000e. Printer je po nekim specifikacijama dosta sličan svom 'bratu' CX1200 no postoji jedna značajna razlika a to je da CX1000e ispisuje po već izrezanim etiketama stoga nije potreban dodatan stroj kao što je FX1200e za završnu obradu. Specifikacije novog pisača su u daljnjem tekstu kao i link na video prikaz njegovog rada.

Postoje dva načina kako reaktivirati Primera toner, koji će vam biti objašnjeni putem videa. Koji god način koristili, pazite da ga ponavljate dok god linije boja ne izgledaju kao na desnoj slici. Sve 3 boje moraju bit jasno vidljive

Treba se uzeti u obzir da je usko grlo snimač medija posebno u slučaju DVDa koji zahtijevaju oko 4min za jedan DVD film pri brzini od 16x. Stoga se po brzini posebno izdvaja Disc Publisher Pro koji ima dva vrhunska Pioneerova Dual-layer drivea što što odmah skraćuje vrijeme posla na pola.
A Disc Publisheri istovremeno i printaju i prže no printanje traje maksimalno 90 sec u slučaju najviše rezolucije od 4800dpi i potpuno ispisane površine.

Količina medija koje možete ispisati, pa time i cijena, ovisi o rezoluciji ispisa koju možete namjestiti od 600dpi do 4800dpi (uvijek u punom rasponu od 16,7 milijuna boja), nadalje o intezitetu boja i njihovoj vrsti te o vrsti površine ispisa na mediju.

Pročitajte sve o brzini printanja, potrošnji tonera, vrsti papira, softveru, rezoluciji printa, prednostima i svemu ostalom što vas može zanimati o ovom label printeru. 

Potrošnja tinte kod LX pisača bitno utječe na ukupnu cijenu izrade etikete, a ovisi o veličini etikete, kvaliteti ispisa i vrlo značajno o samom dizajnu etikete. Maksimalna kvaliteta LX pisača je 4800dpi-a (High Quality), no već kod 2400dpi (Medium Quality) ispis izgleda oštro i kvalitetno, a potrošnja tinte je bitno manja.

PRODAJA PRIMERA HRVATSKA

Finder d.o.o.
Božidarevićeva 13, 10000 Zagreb

tel: +385 1 2337 731
e-mail:prodaja(at)finder.hr

Radnim danom od 9 do 17 sati